Part number list?

[jimp]

OK, I'm lost... or maybe it is. Where's the list of common Connie part numbers cross reference to generic? I can't find it on our site, and half the links on Rick's site are dead.

 

[smithr]

It is the top document in the library under technical documents. http://www.cog-online.org/clubportal/clubdocs/1328/CommonConcoursParts1.pdf Photos[/url]

 

[WaunderinWill]

Here is a text copy of the HTML which I have saved to my hard drive. If you want a copy of it in HTML I will have to figure out how to copy it as such. Common Concours Part Numbers Generic and OEM Accessories: both Factory and Aftermarket Aftermarket Clothing Givi Replacement Keys -------------------------------------------------------------------------------- DISCLAIMER: THESE PN#s HAVE BEEN CHECKED FOR ACCURACY, BUT AS ALWAYS, MISTAKES MAY OCCUR, VERIFY THAT THE PART MATCHES YOUR OLD PART BEFORE INSTALLATION! NEWS FLASH! For any OEM parts not listed here try BuyKawasaki.com If you have any part numbers you would like to contribute, email Bryan Moody link at bottom of page Bryan's Tech Page David Morrow's Tech Page Ron Ayers Motorsports-Genuine Kawasaki Parts for approximately 70% of list price SYSTEM DESCRIPTION GENERIC KAWASAKI SERVICE MANUAL Have this in hand BEFORE starting work! None Available 99924-1065-9 brakes ring, brake piston seal (front & rear) 43049-002 brakes packing, brake piston (front & rear) 43049-1028 brakes front master cylinder cover also used on clutch side 43026-1052 brakes front master cylinder cover diaphragm also used on clutch side 43028-1058 cables cable, speedometer drive Dennis Kirk (Motion Pro) #C9059 54001-1119 cables cable, throttle closing 54012-1303 cables cable, throttle opening 54012-1302 chassis bag antler (bag stay), LH 35011-1300 chassis bag antler (bag stay), RH 35011-1301 chassis bag keys "A" 27008-1127-AA chassis bag keys "B" 27008-1127-BB chassis bearing, steering head LOWER 92116-1009 chassis bearing, steering head UPPER (25mm bore x 47mm OD x 15mm wide) Parts Plus: SSK902 (Rick Nolan) BCA (Federal Mogul): 32005 (Rick Hall) Bower: 32005 get at any bearing supply (see note #1) 92116-1056 chassis bearing, front wheel 86-93 (15mm bore x 42mm OD x 13mm wide) 6302 double seals, get at any bearing supply (see note #1) 601B6302U chassis bearing, front wheel 94-up (17mm bore x 40mm OD x 12mm wide) 6203 double seals, get at any bearing supply (see note #1) 601B6304UU chassis bearing, rear wheel (all years) (20mm bore x 52mm OD x 15mm wide) 6304 double seals, get at any bearing supply (see note #1) 601B6304ZZ chassis bearing, swingarm tapered roller bearing single row (20mm bore x 42mm OD x 15mm wide) Federal Mogul: 32004 NSK: 32004 Bower: 32004 get at any bearing supply (see note #1) 92116-1061 chassis collar, metal collar that goes under mounting screws on belly pan 92027-1935 chassis flap, side cowling LH (fairing extender) WINTER 35019-1193 chassis flap, side cowling RH (fairing extender) WINTER 35019-1194 chassis trim, inner cowling quantity 2 use w/winter side cowling (these are rubber seals that fit between the side cowling and the fairing). 53044-1184 chassis fairing extender KIT Includes both above cowlings and inner trim Less expensive than buying parts separately K99996-1103 chassis footpeg bracket, LH 34003-1259 chassis footpeg bracket, RH 34003-1260 chassis footpeg feelers (bank sensor) 92043-1219 chassis footpeg, LH (metal only) 34028-1198 chassis footpeg, RH (metal only) 34028-1199 chassis fork bushings 44065-1085 chassis fork bushing, inner 44065-1081 chassis fork circlips (fit above seals) 92033-1036 chassis fork seals, inner 92049-1273 chassis fork seals, outer (dust cover) 92093-1232 chassis mirror, LH Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman) 56001-1333 chassis mirror, RH Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman) 56001-1334 chassis plug, (plastic) for allen head bolts 92066-1216 chassis reflector, reflex (for saddlebag) 28012-1077 chassis shift lever pedal assy. 13242-1213 chassis shift lever rubber cover 92075-1175 chassis shock-all years Progressive Suspension: 420-1016 45014-1340 chassis speedometer drive assy 41078-1061 chassis spring, fork-all years Progressive Suspension: 11-1102 44026-1340 (86-93) chassis rear suspension link seal 92049-1109 chassis trim, inner cowling quantity 2 use w/winter side cowling 53044-1184 chassis valve stem, tire 90 degree reccomended on rear wheel for gauge access 16126-1191 chassis valve stem, tire straight 16126-1136 electrical alternator rectifier 13091-1329 electrical battery 12V18AH 7 1/8" L x 3 5/8" W x 6 7/16" H Exide: 18LA (Will Brown) Hawker Odessey: PC680 (Mark Cipriano) Interstate: 18LA (Will Brown) Sears Diehard: 44071 (Kevin Arnold) Super Crank: 18LA (Kevin Arnold) Westco: 12V20L (Mark Cipriano) Yuasa: YB18L-A Sealed Battery: Yuasa: YTX20L-BS 26012-1130 electrical brush, alternator 21039-1052 electrical brush, starter motor 21039-1053 electrical junction box 59416-1060 electrical junction box relays SPDT, 5 amp DC contact rating 12 VDC coil Aromat: JS1E-12V NTE: R46-5D3-12 (NTE is a nationally distributed replacement parts brand, try your local electronic part house or http://www.mouser.com/ ) thanks to Rick Nolan for the NTE number electrical key blank Ilco: KA14 Taylor: X103 27008-1103 electrical lamp, headlamp bulb, 100/80 NAPA: BP1210/H4 ($10.99) 92069-1002 electrical headlamp socket NAPA LS 6235 (bakelite) (Jim ****inson) or 1984 Honda Accord get from junkyard, will not melt when used with high wattage bulbs SEE NOTE 2 BELOW electrical lamp, taillamp 12V 27/8W 1157 92069-059 electrical lamps, clock 12V3W T-7 74 (Guy B. Young II) 92069-1020 electrical lamps, dash 12V 3.4W 194, Suggest Sylvania:194LL (long life) 92069-1007 electrical lamp, front running light/turn 32/3CP (23/8W) 1157 92069-060 electrical lamp, rear turn signal 32CP (23W) 1156 92069-055 electrical switch, cooling fan Also used on 1991 Honda Civic DX ACDelco: E-1858 Auto Tune: PT2628 Beck/Arnley WorldParts: 201-0817 Beck/Arnley WorldParts: 201-1369 Borg Warner: TFS500 (Tom Masterson) Echlin (NAPA): FS-130 Facet: FS8404 (Chris Roy) Filko: TFS-1 (Bob Chappell) Four Seasons: 35934 (Bob Chappell) G.P. (?): 40-5001 Kem: TW-65 Mitech: TS-84 Motorcraft: no interchange Niehoff: WA-639B Standard: TS-84 Wells: SW504 (Guy B. Young II) 27010-1202 electrical switch, ignition 27005-5064 electrical turn signal flasher unit Tridon-Stant: EP34 (Guy Young) 27002-1060 electrical switch, kickstand (86) 27010-1214 electrical switch, kickstand (87 up) 27010-1220 electrical switch, neutral (gasket 92065-058) 13151-1080 electrical wiring harness '86 (superseded by below) 26001-1773 electrical wiring harness '87 to '91 26001-1838 electrical wiring harness '90-93 26030-1038 electrical wiring harness '94-up 26030-1252 electrical wiring harness (front) 86-93 26001-1774 electrical wiring harness (front) 94-up 26030-1285 engine clutch nut MUST be used with the new star springs 92015-1929 engine clutch star spring, 2 required (be sure to replace the nut at the same time) 39130-1071 engine clutch pushrod seal Chicago Rawhide (SKF) 3077 8mm ID, 18mm OD, 7mm wide get at any bearing supply 92049-1165 engine counterbalancer seal Chicago Rawhide (SKF) 7202 19mm ID, 27mm OD, 5mm wide get at any bearing supply 92049-1174 engine filter, air K&N: KA9084 (Rich Doell) 11013-1112 engine filter, oil CarQuest: 89941 (Will Perkins) Emgo: 10-37500 (Dave Mamanakis) Fram: CH6012 Hastings: LF571 (John Hinton) Honda: 15410-300-024 (Dave Mamanakis) Honda: 15410-426-010 (Dave Mamanakis) NAPA: 4941 (Dave Mamanakis) Perf-Form: J-501 (Dave Mamanakis) Purolator: ML16812 (Dale Horstman) STP: SMO-12 (Kevin Cummings) Triumph: 1210031 (Dave Mamanakis) Vesrah: SF-4004 (Doug Donner) WIX: 24941 (David Ritchie) Yamaha: 36Y-13441-00 (Dave Mamanakis) 16099-003 engine filter, oil Flat washer that goes on top of spring (you know, the part that always gets lost) 20.5mm id X 30mm od X 1mm thk. 92022-1012 engine gasket, engine side cover, RH 11009-1860 engine gasket, neutral safety switch 92065-058 engine gasket, reed valve 11009-1379 engine gasket, pulsing cover (left side) 11060-1695 engine gasket, valve cover 11009-1378 engine gasket, valve cover spark plug well 11009-1377 engine radiator hoses From Michael Thompson NAPA hoses: NAPA #7741 (Gates 21029, 2000 Suzuki Swift Lower Hose) 1"/25.4mm ID This one gets cut into several pieces to replace the hoses at the front of the engine to the water pump. NAPA #H151 (1"/25.4mm ID bulk hose) This is a straight hose. A piece a foot long is more than enough to replace the straight hose from the thermostat housing to the filler assembly. The final hose, from the filler to the top of the radiator, I bought from a local dealer. P/N 39062-1164 Some have said that a second NAPA #7741 will work there, but I didn't like the way it looked there. engine radiator cap (32mm ID x 16mm deep neck) 0.9bar / 13psi Same as 1978 Ford Fiesta Carquest :33028 (Guy B. Young II) Stant: 10227 (boxed) (Guy B. Young II) Stant: 11227 (blister pack) (Guy B. Young II) Stant: 10229 (Bryan Moody) CST: 7013 (Bryan Moody) Motorcraft: RS62 (Bryan Moody) Motorcraft: RC19 (Bryan Moody) Beck/Arnley: 133-8060 (Bryan Moody) Beck/Arnley: 133-8078 (Bryan Moody) Gates: 31527 (Bryan Moody) AC-Delco: RC19 (Bryan Moody) 49085-1053 engine shift lever (to transmission shaft) THIS IS THE ONE THAT USUALLY BREAKS 13242-1195 engine spark plugs, platinum NGK: D8EVX engine spark plugs, standard NGK: D8EV ACDelco: R121XLS 92070-1011 engine spark plug cap 21160-1065 engine thermostat Also used on 1983 Honda Accord ACDelco: 131-17 Carquest: 31068 (Guy B. Young II) Futaba: R124 (Kevin Arnold) Mitsubishi: MB221855 (Kevin Arnold) NAPA: 142 (Guy B. Young II) Pep Boys: 29368 (Guy B. Young II) Stant: 13368 (boxed) (Guy B. Young II) Stant: 35368 (blister pack) (Guy B. Young II) Toyota: 16401-63010 (Kevin Arnold) 49054-1051 engine thermostat o-ring 32mm OD x 25mm ID x 3 mm McMaster-Carr (viton) PN#9263K275 $9.90 pk/10 (buna-n) PN#9262K275 $7.74 pk/50 92055-112 engine valve cover, Europe/Canada model (does not have provision for reed valves) 14024-1082 engine washer, head cover bolt (the cup shaped washer that the valve cover bolts go thru) 92022-1487 engine Water Pump Rebuild Kit K&L: 15-4343 engine water pump oil seal Chicago Rawhide (SKF): 4752 12mm ID x 28mm OD x 7mm wide (Mark Cipriano) 92049-1416 engine water pump external pump o-ring, 33mm 92055-1266 engine water pump impeller Cover o-ring 92055-1271 fuel carb bowl o-ring 92055-1222 fuel carb needle (float valve) clamp 16044-007 fuel carb needle (float valve) 16030-1007 fuel petcock to tank o-ring 51039-010 fuel petcock lever o-ring 92055-1027 fuel petcock assy. (complete) 51023-1130 fuel petcock diaphagm cover 16146-1005 fuel petcock diaphragm assy. 43028-1015 fuel petcock diapragm o-ring 670B1504 fuel petcock lever spring 92081-1171 tools Microfiche ZG1000A1-A3 (covers 86-88 models) Why buy it? Go to BuyKawasaki.com 99961-0211 tools Hex Drive Socket (12mm 1/2" Drive) fits front axle McMaster-Carr PN#5571A68 $9.04 ea. tools Hex Key (12mm Long Arm) fits front axle McMaster-Carr PN#6958A19 $3.94 ea. tools Socket 27mm fits rear axle and rear drive fill plug (1/2" drive) McMaster-Carr PN#7149A29 $7.51 ea. tools Wrench, spanner-steering head Metric Fixed Head Hook Style Spanner Wrench For 40-42mm Circle Dia McMaster-Carr PN#6975A16 $11.02 ea. tools ABS Cement-used for repairing broken body panels McMaster-Carr PN#74605A54 $2.16 ea. ( 8 oz) PN#74605A51 $3.56 ea. (16 oz) PN#74605A52 $5.89 ea. (32 oz) Note #1: online bearing and seal sales atA&W Bearing or Johnson Bearing Note #2: Be sure to check that the female sockets in the plug are TIGHT on the bulb. I have had problems with this and burnt up the NAPA plug. ACCESSORIES Prices are approximate, your cost may vary, shop around! Other parts Larry Buck purveyor of fine Concours products Lightbars, helmet relocation brackets, conspicuity products, racks, CB mounts Bryan Moody Fuel Cell Kits, Rifle windshield shelving system Sampson Sport Touring Fuel Cells, Luggage Racks Givi Key Info Givi Replacement keys are available from most lock shops. Use an ILCO X226/HYD12 blank (Dr. Squido Calamari) Factory extended windshield K53020-083 $209.95 Factory trim for above 53044-1196 $9.95 Factory luggage rack K53020-083 $117.95 Factory Backrest and pad 86-93 models K53043-052 $76.95 Factory Backrest and pad 94-present models K53043-052A $84.95 Factory adaptor to mount backrest and pad to luggage rack K53021-083 $84.95 Factory saddlebag liners Black/Red K99994-335 $65.95 Factory saddlebag Liners Black/Gray K99994-337 $65.95 Factory Air Deflectors (similar to Baker Air Wings) K53003-020 $69.95 Factory Fairing Extender Kit (contains both side extensions and trim) K99996-1103 $64.95 Factory Tank Bra K99994-918 $30.00 Jet Kit by Factory Pro K21 Rifle Windshield system http://www.rifle.com $199.00 standard price Rifle base ONLY 0.201.1116 $129.00 Rifle windshield ONLY 15" clear 0.211.0001 $70.00 Rifle windshield ONLY 17" clear 0.211.0002 $70.00 Rifle windshield ONLY 19" clear 0.211.0003 $70.00 Rifle windshield ONLY custom 0.211.0004 $95.00 Rifle windshield ONLY 15" tinted 0.211.0011 $80.00 Rifle windshield ONLY 17" tinted 0.211.0012 $80.00 Rifle windshield ONLY 19" tinted 0.211.0013 $80.00 Rifle windshield ONLY custom 0.211.0014 $105.00 Baker Air Wings-the genuine article CONAW http://www.bakerbuilt.com/ $49.95 Race Tech Cartridge Emulators (94 up) FEGVS3801 $139.95 BMW Type Electrical Connector (John Deere) RE11344 PLUG AL25073 SOCKET CLOTHING Clothing-Lands End Turtleneck Sweaters From David Neal, COG #32 And if you're interested in their turtlenecks: 1. These are some of the handiest, most versatile motorcycle wear I have (along with wool military sweaters in silverdammit, natch). 2. Land's end lists only 100% cotton in their catalog, but they do sell a mixture (70/30 or 60/40-I forgot). My old Land's End turtlenecks were 50/50 cotton/poly blend, and I thought the mix felt softer than the 100% cotton variety. 3. No experience with Land's End logo, but on the ones I had done in town years ago (before the logo was set up with Land's End) I noted that when on the garment, the silver thread looked gray, and the white thread looked silver. The white seemed to reflect light more, giving a silver hue to the logo. I preferred the white thread to the silver thread, as it stood out a bit more. Don't know if the same holds true for Land's End logo work, but I'll know in a week or so. 4. I ordered 'em with the old COG logo (and the words Concours Owners Group) on the neck, offset to the (wearer's) right. If you decide you'd like to have a few of these WITH logo, you'll have to call the Land's End corporate department (800) 338-2000. The turtlenecks are $17.50 each/logo $5.30 extra. The logo number is 922906K, and don't forget to specify the thread color (no extra charge) when ordering. David R. Neal Danville, VA. AMA Life Member COG #32 Any technical information you would like to contribute? Click here! BACK TO THE CONCOURS TECH PAGE

 

[hachayalboded]

Bryan Moody Fuel Cell Kits, Rifle windshield shelving system Any more information on these items?